Defective font card installed in font slot. Any help here would be appreciated too. Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller. If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed. Toner Low Toner sensor detects low toner.
|Date Added:||27 November 2006|
|File Size:||63.86 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
If one of these errors appeared during Lexmark optra se 3455, or while the printer was idle not printing or receiving dataor while trying to print one optraa the internal test pages, replace the system board. If the tray is difficult to remove, then you may have to remove the tray above or below tray X to remove the jammed pages. Can also be LVPS or system board. We got it this 345 and I lexmark optra se 3455 it installed. Page too complex to print.
Remove toner cartridge for better access to jammed paper. A secondary error indication can be obtained by pressing an releasing a button.
Check the continuity of the fuser lamp at the two heavy leads. Go to Enterprise Business. Fuser lexmzrk too hot while printing or when idle.
It can also be the LVPS low voltage power supply or a fuse in the power supply on some models. The engine is experiencing unreliable communication with the specified device. Printhead Error – May have sub-codes. Font card format not supported by printer.
Check printhead, cable, motor, system board. The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure. Check connections to the to lexmark optra se 3455 card assembly. Power printer off one to two minutes. The wrong printhead is installed. The Transfer drum has reached the end of it’s life and must be replaced.
If an open circuit, replace the lamp or fuser. Run the Quick Disk Test. The pin should enter the tower on the HVPS and depress the cover switch. Great that you have that part in stock and thank you for your quick reply. Input sensor not made after pick attempt. Make sure there is lexmark optra se 3455 between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct.
The main motor assembly may need to be replaced. Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. Observe the lamp through the left near side of the lexmark optra se 3455.
Make sure the memory shown on the printout matches the installed memory. Remove and reinstall print cartridge. In general, fuser errors require replacement of the fuser as a cost effective repair.
Lexmark Printer Drivers
I am new to this and do optea want to lexmark optra se 3455 this up. Input Paper Sensor was not triggered – Paper may be jammed at the sensor. If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and lexmark optra se 3455 sure the left bearing of the transfer roll is making proper contact.
Replace the bump alignment motor. If optrq, connectors and connections are good replace assemblies listed. Duplex Cover Open Top cover of duplex unit is sensed open.
Check the TMC pin in the lexmark optra se 3455 contact error for free non binding movement If pin does not move freely you may need to replace the contact assembly. Also, can I get some instructions on putting in the rollers. The engine protocol violation detected by the specified device.
Check fan connector and cable for loose or lexmark optra se 3455 connection. Replace the disk if instructed by the operator panel. Whether your business fills a room or circles the globe, Lexmark offers the imaging solutions, technologies and services you need to succeed.
404 Not Found
Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed. Genuine Lexmark Supplies deliver superior image quality, while also producing lexmark optra se 3455 volumes and reducing cost per page.
Serial Error – Framing or parity error on serial. Install maintenance kit and reset maintenance message Purchase Lexmark maintenance kits How did we do? Check the toner metering cam on back of suspect cartridge. Lexmark optra se 3455 further measurement The printhead laser scanner does not contain any serviceable parts. Verify latch relay is operating – slowly close door and listen for interlock switch 3.
Thank you for the speedy shipment and response. If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. Can be system board or printhead. When this message is displayed, do not remove accumulated sheets during the jam clearance procedure as the printer will not reprint the removed sheets.